About Us
Factory Tour
Quality Control
Contact Us
Request A Quote
Home ProductsGPS Fuel Sensor

Fuel Tank Level Sensor Petrol Level Sensor Used To Fix The Extention Wire

I'm Online Chat Now
We are very satisfied with your CA-V1 and CA-V1, CA-V6W for professional customers, CA-V6W is a very good product on the motorcycle,thanks!

—— Touya_ra

now we already used your company CA-V6 more than 2000Pcs, thanks for your company best support, we will expend this business in all of the Kenya

—— Nancy Saruni

your device CA-V1 is very good for our customer project, it is so proffesional , we can use in refrigerator car which can test the temperature ,thanks

—— Rajesmay

Fuel Tank Level Sensor Petrol Level Sensor Used To Fix The Extention Wire

small.img.alt small.img.alt

Large Image :  Fuel Tank Level Sensor Petrol Level Sensor Used To Fix The Extention Wire Get Best Price

Product Details:
Place of Origin: China
Brand Name: caxtrack
Certification: CE/ROHS/FCC/SGS
Model Number: CA-201
Payment & Shipping Terms:
Minimum Order Quantity: 10 pcs
Price: negotiation
Packaging Details: Packed in carton firstly
Delivery Time: 1-10 working days after received your payment
Payment Terms: T/T or western Union or paypal
Supply Ability: 100,000pcs per month
Detailed Product Description
Product Name: Fuel Sensor Application: Mixer Truck
Work Voltage: 9-36V Shell: Protective
15CM Cable Tie: Used To Fix The Extention Wire Abrasive Paper: Used To Clean The Bottom Of The Tank
Working Temperature: -30℃~+75℃ Inbreaking Protection: IP66
Peripheral Interface: RS232 / RS485 / Analog Transmission Length: 40cm-150cm
High Light:

battery gps tracker


gps tracker with fuel sensor

RS232 / RS485 / Analog transmission Capacitor Oil Level Sensor


Examination area: 100~1000mm

resolution ratio: 0.1%

Measuring accuracy:0.1%

Maximal error of measure :1mm

heat-resistant :-40~150

Diameter Φ18mm

Output signal :4~20mA,0~5V, RS485, RS232, CAN bus

Voltage supply :DC7~42V

Rated supply :0.1W

Fixed type :Screw installation M20X1.5 OR Flange mounting

Pressure range :-0.1MPa ~ 0.1 MPa

ambient temperature -40~85℃

Fuel Tank Level Sensor Petrol Level Sensor Used To Fix The Extention Wire 0


2.1 definition of the output line

Interface output line use 6 core cable, connecting definition:


0~5V output [CA-201A]:

Black line connect ground wire

Red line connect positive power

White line 0~5V voltage signal output,connect voltage signal wire

Yellow line empty fuel tank use only

Green line full fuel tank use only


4~20 mA output [CA-201B]:

Black line connect ground wire

Red line connect positive power

White line 4~20mA ampere signal out put,connect ampere signal line

Yellow line empty fuel tank use only

Green line full fuel tank use only


RS232 output [CA-201C]:

Black line connect ground wire

Red line connect positive power

White line RXD input, connect car RS232 TXD

Blue line TXD output, connect car RS232 RXD

Yellow line empty fuel tank use only

Green line full fuel tank use only


RS485output mode(CA-201D)

Black line connect to CND

red line connect to VDD

white line connect to RS485 A

blue line connect to RS485 B

yellow line marking for empty fuel tank

green line marking for full fuel tank


2.2 Calibration

This sensor adopt high-speed MCU of CNC technology, adopting self-calibration

Calculation , and leaves out the complicated Manual calibration while using. in normal

circumstance, the sensor can directly be used in the measurement of the diesel, if need to calibration, you can use the three following ways to complete. (each can work)


1.self-calibration: put the sensor slowly into the The tested medium while power on, let the liquid get into the feed inlet slowly ,stoping when the liquid is overflew the vent hole of the sensor. and this operation accomplish the calibration of the sensor . In order to prevent the failure of the calibration process , please do this process for at least 2 times .( notice:This way is under the condition of powering on , outage restart will restore the factory Settings.In the condition of empty fuel tank,refueling to full, the sensor itself are also able to complete the self-calibration )





1.Only one signal can exist among RS232/ RS485/ 0-5V/ 4~20mA, and you can use either one of them. The trunk of RS485 can meet multiple sensors at the same time, but you should set the address of each sensor in advance. Address of each sensor must be unique, in case the trunk is locked. RS485 trunk is made of half-duplex chips, so when it reading data, you should set aside the corresponding time for the module. The reading speed cannot be too fast: when it reads continuously, the time interval between the two instructions cannot be less than five seconds.

2.For the signal transmission line, especially the one of RS232,communications circuits should not be too long, and should use the shielded wire.

3. For the sensors of the signal RS232/ RS485, when debugging the failure of communication, you can exchange the white line and the blue one and test again. If it works then, it is the connection error before. The operation is only for digital communications.

4. The power supply voltage of sensor cannot be more than the normal working voltage, and the power consumption of the sensor’s power supply cannot be less than the normal working power consumption.

5. The actual environment should conform to the requirements of the basic parameters of sensors, and shall not exceed the normal range, or it would damage the sensor, even cause other accidents.

6. On account of oil products, there are differences between the mediums of the calibration and use, users had better operate according to 2.2.2.

7. Do not remove sensors or damage it maliciously, or we do not guarantee it.

8.General factory accessories include Flange, rubber blanket, O-Rings, booklet of instruction, certificate of conformity. If you have special needs, please tell us in advance.

9.Guarantee period of the sensor is one year. All accessories including rubber blanket, O-Rings, are beyond the scope of “ threeguarantees ”.




Symptom of failure

1No-output /communication error

2The output value unchanged

3Measurement error of output value

4Output value floats up or down


cause analysis

1 Open circuit of the power or voltage too low

Sensor fault

Wrong connection of the lines and wires

2 service voltage abnormal

external interference

Sensor jammed

Sensor fault

3 service voltage abnormal

external interference

Sensor jammed

autoadaptation uncomplete

Sensor fault

4 oil level flow

service voltage abnormal

external interference

Sensor fault


Exclusion and solutions

1test connect→test if the voltage is greater than 10V when load→test the supply current [range 3~10mA] → connect method see 2.1,or change over blue and white line[digital communication only]→if all above is regular or current beyond normal range,the sensor occurred failure.

2Test the supply voltage when load[ex.voltage unstable] → recharge the sensor →test if there is a serious interference around→test whether sensors hole is blockage from top to bottom → execute 2.2.2→If not,the sensor occurred failure.

3 detect whether service voltage is stable while loading ( if the voltage is unstable) → →whether external have interference→check whether the sensor is jammed → execute the 2.2.2 process →then it should be the sensor fault

4 check the oil leve is stable → check the service is normal and functional →whether external have interference →execute the 2.2.2 process→then it should be the sensor fault




1 4~20mA output supply voltage DC20~28V,current is 4~20mA except communication output

2Check the tank oil level is float or not,if become regular after recharge,check the interference and the power

3 it usually can be functional while executing the 2.2.2 process

4 it usually occur on 0~5V signal





The ultrasonic fuel level sensor is used for digital recording vehicle refueling, to prevent driver stealing oil , avoid the waste of resources, improve operational efficiency, and improve the traffic safety, strengthen the operation and management level.

       This sensor is applicable to various types of vehicles such as trailers, taxis, buses, concrete mixer truck, engineering machinery, sanitation trucks and other.




1. All of our product is free to use the Tracking service server in 24 hours each day

2. All of our product there is a 2 year quanlity assurance.

3. Sample fee will not  be returned.



Product Configuration:


1. Standard configuration

1)    main device             1 pcs

2)    power line                1 pcs

3)    sensor

5)    Installation cables    1 set

6)    Usage instructions  

7)    Warranty card


Contact Details

Contact Person: Peter

Tel: +8613717161241

Send your inquiry directly to us